攪拌車進行供水操作時要注意什么？
每次我們操作全自動攪拌車時，水都是用于正常工作的重要材料，因此，在裝填所生產的混凝土之前，每次都應加水。那么攪拌車進行供水操作時要注意什么？全自動攪拌車廠家為您解答。
Every time we operate the automatic mixer, water is an important material for normal work. Therefore, water should be added every time before the concrete produced is loaded. So what should be paid attention to when the mixer truck is operating for water supply? The manufacturer of the fully automatic mixer will answer for you.
采用水泵供水：
Water is supplied by water pump:
a、先打開駕駛室里的水泵翹板開關，再打開蜂鳴開關，水泵即可工作，同時，蜂鳴器發出“嘟嘟嘟”的叫聲；
a. First turn on the rocker switch of the water pump in the cab, then turn on the buzzer switch, and the water pump can work. At the same time, the buzzer gives a "beep beep" sound;
b、向攪拌筒內加水或沖洗料斗槽時，開啟“料斗”閥門；
b. When adding water to the mixing drum or flushing the hopper tank, open the "hopper" valve;
c、沖洗出料溜槽時，開啟溜槽閥們；
c. When flushing the discharge chute, open the chute valves;
d、沖洗車身時，先開啟水槍閥門，而后可直接使用車尾水槍；采用氣壓供水：
d. When washing the body, first open the water gun valve, and then directly use the tail water gun; Pneumatic water supply:
①先打開駕駛室供氣開關，當主車壓力表達到8kg/cm2壓力再打開供水系統手動氣開關，當壓力表達到2kg/cm2壓力時即可工作。
① First turn on the air supply switch in the cab. When the main vehicle pressure reaches 8kg/cm2, turn on the manual air switch of the water supply system. When the pressure reaches 2kg/cm2, it can work.
②向攪拌筒內加水，沖洗料斗槽、卸料槽時，先開啟水箱底部閥門，再開啟“料斗”閥門。
② When adding water to the mixing drum and flushing the hopper tank and discharge tank, first open the valve at the bottom of the water tank, and then open the "hopper" valve.
③沖洗車身時，先開啟水箱底部閥門，后直接使用車尾沖洗裝置。
③ When washing the body, first open the valve at the bottom of the water tank, and then directly use the rear washing device.
此外攪拌罐中應泵入多少氣壓，該壓力已在工廠設定，無需調整。如果有特殊情況需要調整，建議將壓力控制在3.5Mpa左右，如果壓力過高，很容易爆炸。此外，在日常使用新的混凝土攪拌車中，有必要隨時擰緊管接頭以防止其脫落。
In addition, how much air pressure should be pumped into the mixing tank, which has been set in the factory and does not need to be adjusted. If adjustment is required under special circumstances, it is recommended to control the pressure at about 3.5Mpa. If the pressure is too high, it is easy to explode. In addition, in the daily use of new concrete mixer trucks, it is necessary to tighten the pipe joints at any time to prevent them from falling off.
每個攪拌車供水的布置都相似。通常，水箱中的水裝滿后，關閉填充閥。在不用時，將操縱桿的位置放在中間。冬季每天結束工作后，應將水箱和水管中的水排干，并使用水管中的壓縮水吹掉每根管子中的殘留水，以防止水管結冰后破裂。
The arrangement of water supply for each mixer truck is similar. Normally, when the water tank is full, close the filling valve. When not in use, place the lever in the middle. At the end of each day's work in winter, the water in the water tank and water pipe shall be drained, and the compressed water in the water pipe shall be used to blow off the residual water in each pipe to prevent the water pipe from cracking after freezing.
作為廠家，我們建議您在使用全自動攪拌車時保持一個好的使用習慣，及時沖洗和進行各種準備工作可減少攪拌車的故障發生。更多相關內容就來我們網站http://www.pheenet.cn咨詢吧！
As a manufacturer, we recommend that you keep a good usage habit when using the fully automatic mixer. Timely flushing and various preparations can reduce the occurrence of mixer failures. More relevant content will come to our website http://www.pheenet.cn Consult!
