自動上料攪拌車的清洗要點你了解嗎？
今天我們中科聚峰廠家的小編就來給您介紹自動上料攪拌車的保養注意事項，希望通過我們的介紹讓您對自動上料攪拌車的保養注意事項等問題有更深入的了解
Today, our small editor from Zhongke Jufeng factory will introduce the maintenance precautions of the automatic feeding mixer to you. I hope that through our introduction, you can have a deeper understanding of the maintenance precautions of the automatic feeding mixer
1、在施工現場卸料完畢后，應立即用攪拌車隨帶的軟管沖洗進料斗、出料斗、卸料溜槽等處，粘附在車身各處的污泥及混凝土。在返回攪拌站的途中，應向攪拌筒內注150---200L水以清洗筒壁及葉片粘結的混凝土殘渣。
1. After unloading at the construction site, the inlet hopper, discharge hopper and discharge chute should be flushed with the hose attached to the mixer to remove the sludge and concrete adhering to the vehicle body. On the way back to the mixing station, 150-200l water should be injected into the mixing drum to clean the concrete residue bonded by the cylinder wall and blades.
2、每天工作結束后，司機應負責向攪拌筒內注入清水并高速(14—18轉/分)旋轉5—10分鐘，然后將水排去，以保證筒內清潔。用高壓水清洗攪拌筒各個部分時，應注意避開儀表及操縱桿等部位。壓力水噴嘴與車身油漆表面間的距離不得小于40厘米。
2. At the end of each day's work, the driver should inject fresh water into the mixing drum and rotate it at high speed (14-18 RPM) for 5-10 minutes, and then drain the water to ensure the cleanness of the drum. When cleaning each part of the mixing drum with high pressure water, pay attention to avoid the instrument and control rod. The distance between the pressure water nozzle and the paint surface of the vehicle body shall not be less than 40 cm.
3、攪拌筒內外積污及殘存的混凝土渣塊時，以及在機修人員進入筒內進行檢修和焊補作業時，需先關閉汽車發動機，使攪拌筒完全停止轉動。在機修人員進入筒內工作期間，必須保證拌筒內通風良好，空氣新鮮，無可然氣體及有害灰塵，氧氣供應充足。在筒內使用電動工具操作時，操作人員必須有良好的絕緣保護。
3. When removing the dirt inside and outside the mixing drum and the remaining concrete slag, and when the machine maintenance personnel enter the cylinder for maintenance and welding repair, it is necessary to turn off the automobile engine to stop the mixing drum completely. During the period when the machine maintenance personnel enter the cylinder, they must ensure that the mixing drum is well ventilated, the air is fresh, there is no natural gas and harmful dust, and the oxygen supply is sufficient. When using electric tools in the cylinder, the operator must have good insulation protection.
4、工作時，不得將手伸入旋轉的攪拌筒內，嚴禁將手伸入主卸料溜槽和加長卸料溜槽的連接部位自動，自動上交攪拌車在工作時應注意什么以免發生事故。
4. When working, do not put your hand into the rotating mixing drum. It is strictly forbidden to put your hand into the connection between the main discharge chute and the lengthened discharge chute. It will automatically hand over to the mixer truck what should be paid attention to when working to avoid accidents.
以上是關于自動上料攪拌車的清洗要點的相關內容介紹，希望對大家有所幫助，想要了解更多內容歡迎點擊中科聚峰廠家www.pheenet.cn官網。
The above is about the automatic feeding mixer cleaning points related content introduction, hope to help you, want to know more content, welcome to click Zhongke Jufeng manufacturers www.pheenet.cn Official website.
